Updated November 2026

A diy bike pump holder keeps your floor pump or frame pump where you can reach it, without rattling loose on the garage wall or bouncing off the frame on a rough trail. The options below were compared on mounting method, frame compatibility, tube diameter range and how much installation work they need. Each one suits a different kind of rider or bike.

Our top picks at a glance

  1. 1Pump Frame Mount Clip ABS Cylinder Bracket HolderTOP CHOICEBest overallPump Frame Mount Clip ABS Cylinder Bracket HolderView on Amazon
  2. 2SKS 2-Point Pump Holder 23-29 mmBest for a 2-point mount on standard tubesSKS 2-Point Pump Holder 23-29 mmView on Amazon
  3. 3Bike Pump Holder Compatible with Cube E-MTB FrameBest for e-MTB framesBike Pump Holder Compatible with Cube E-MTB FrameView on Amazon
  4. 4TwoFish Bike Block Pump HolderBest for a simple strap-and-block setupTwoFish Bike Block Pump HolderView on Amazon

Our Top Picks

Quick Comparison

Product Best for Key feature
Pump Frame Mount Clip ABS Cylinder Bracket Holder General frames Lightweight ABS bracket
SKS 2-Point Pump Holder Standard 2-point mounting Fits 23–29 mm pumps
Bike Pump Holder for Cube E-MTB Frame Cube e-MTB owners Uses bottle cage screws
TwoFish Bike Block Pump Holder Simple strap mounting One strap and block

Pump Frame Mount Clip ABS Cylinder Bracket Holder

Pump Frame Mount Clip ABS Cylinder Bracket Holder, Fits Most Bicycle Tubes, Lightweight Cycling Accessory

Pump Frame Mount Clip ABS Cylinder Bracket Holder, Fits Most Bicycle Tubes, Lightweight Cycling Accessory A related read: Bike Phone Mount DIY: Build a Safe Handlebar Holder in 6 Steps.

View on Amazon

Best for: general frames and fitting most bicycle tubes

This is a good fit for riders who want a light, simple bracket that works across several frame types without a dedicated mounting kit.

Pros:

  • Lightweight ABS construction
  • Designed to fit most bicycle tubes

Cons:

  • Fit depends on the tube diameter, so measure before buying

View on Amazon

SKS 2-Point Pump Holder 23-29 mm

SKS 2-Point Pump Holder 23-29 mm (5 Units) Unisex Adult, Black, One Size

SKS 2-Point Pump Holder 23-29 mm (5 Units) Unisex Adult, Black, One Size

View on Amazon

Best for: standard 2-point mounting on pumps in the 23–29 mm range

This suits riders with a pump in a common diameter who want a secure two-point hold that stays put on rough ground.

Pros:

  • Two-point clamp resists rotation
  • Covers a 23–29 mm diameter range

Cons:

  • Pumps outside the stated diameter range will not fit

View on Amazon

Bike Pump Holder Compatible with Cube E-MTB Frame

Bike Pump Holder Compatible with Cube E-MTB Frame | Fits Wide E-MTB Frames | Replaces Pump Mount | Easy Install with Bottle Cage Screws

Bike Pump Holder Compatible with Cube E-MTB Frame | Fits Wide E-MTB Frames | Replaces Pump Mount | Easy Install with Bottle Cage Screws

View on Amazon

Best for: e-MTB frames that need a pump mount

This is aimed at owners of wide Cube e-MTB frames who want a mount that installs through existing bottle cage screws instead of drilling.

Pros:

  • Installs with bottle cage screws
  • Designed for wide e-MTB frame tubes

Cons:

  • Specific to Cube-style frames, so check compatibility first

View on Amazon

TwoFish Bike Block Pump Holder

TwoFish Bike Block Pump Holder: One Strap and Block

TwoFish Bike Block Pump Holder: One Strap and Block

View on Amazon

Best for: simple strap-and-block mounting with minimal setup

This works well for riders who want a quick, tool-free mount that can be moved between bikes or removed when the pump is not needed.

Pros:

  • Single strap keeps setup quick
  • Easy to move between frames

Cons:

  • Less rigid than a bolted mount on very rough terrain

View on Amazon

Buying Guide

Check your mounting points

Look for existing bottle cage bosses or pump mounts on the frame. Clamp-style holders work on most tubes, while bolted or screw-in holders need threaded points.

Measure the pump barrel

Most floor and frame pumps have a barrel between roughly 23 mm and 29 mm, but measure yours with a caliper or tape. A holder that is too loose will rattle, and one that is too tight can crack the barrel.

Consider how often you move the pump

A strap or block suits a pump you take on and off often. A bolted holder is better if the pump stays on the bike for long rides.

Plan for trail vibration

Two-point clamps resist rotation better than single-point mounts. Owners often report that single-strap holders loosen over long descents, so check the fit after the first few rides.

Good picks for this: SKS 2-Point Pump Holder and Pump Frame Mount Clip ABS Cylinder Bracket Holder

FAQ

Can I mount a pump holder on any bike frame?

Most holders need either bottle cage screw bosses or a clean section of tube. Check your frame’s mounting points and the holder’s listed compatibility before you buy.

Will a holder damage my frame paint or tubing?

Rubber or ABS contact pads reduce scratching, but tight clamps can mark paint over time. Fit the holder with a light torque and check it periodically. A bike shop can advise if you are unsure about a carbon frame.

Do I need tools to install a pump holder?

Strap and clip-style holders usually need no tools, while bolted mounts need a hex key or screwdriver. Follow the manufacturer’s installation instructions for your specific model.

Conclusion

For a general-purpose mount, the Pump Frame Mount Clip ABS Cylinder Bracket Holder is a flexible starting point. The SKS 2-Point Pump Holder suits riders who want a secure hold on standard pump barrels, while the Cube-compatible mount is the right choice for e-MTB owners. The TwoFish strap-and-block holder works best for quick, tool-free setups.

Sources

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our bike accessories guides, checking product details against manufacturer specifications and owner feedback.